Bosch GKS18V-25CN 18V circular saw
The GKS18V-25CN is the bare tool: no battery, no charger.
Published manufacturer specifications; sources last checked 2026-10-25.
Specifications
Blade diameterWhat this meansBlade diameter mainly sets how deep the saw can cut. Larger blades cut deeper, which matters for 2x lumber at a bevel and for thicker stock. Check the maker's listed cut depth at 90 and 45 degrees, and buy replacement blades in the stated diameter. | 7-1/4 in |
| Max cut depth at 90 degrees | 2-1/2 in |
| Max cut depth at 45 degrees | 1-13/16 in |
Max speedWhat this meansMax speed is the top no-load speed, in RPM for rotating tools. No-load means the tool is running free, so speed drops once it is working. On drills, many makers list a figure per gear: high for small bits, low for control with large bits or long screws. | 5,000 RPM |
Max bevelWhat this meansMax bevel is the largest angle the shoe can tilt for angled cuts, measured from square (0 degrees). Most saws reach at least 45 degrees; some go further, which helps with roof and stair work. Positive stops at common angles make repeat cuts quicker and more consistent. | 50 degrees |
Batteries in boxWhat this meansThis lists how many batteries come in the box, if any. Tool-only (bare) listings include no battery or charger, which suits buyers already on that battery platform. Two batteries let you charge one while working with the other. | 0from the box list |
Battery capacity (each)What this meansAmp-hours (Ah) is the battery's charge capacity. At the same voltage, a higher Ah pack runs longer between charges but is usually larger and heavier. Smaller packs keep the tool lighter for overhead and light work; larger packs suit saws, grinders and other high-draw tools. | None includedfrom the box list |
Charger in boxWhat this meansThis states whether a charger is included and which type. Chargers vary in output, so the same battery can take noticeably different times to charge on different chargers. Tool-only listings usually include no charger. | Nofrom the box list |
Tool lengthWhat this meansTool length is the front-to-back measurement published by the maker. A shorter tool fits between studs, joists and inside cabinets more easily; standard US framing is 16 inches on center, leaving about 14-1/2 inches between studs. Check whether the figure includes the chuck or bit holder. | 15.6 in |
WarrantyWhat this meansThis is the maker's published warranty term. Terms for tools, batteries and chargers often differ, and some depend on registration or exclude certain uses. Read the maker's terms for what is covered, how claims are handled and whether proof of purchase is required. | 5 Year Limited Warranty (tool) |
Buying options
Battery and charger not included. See box contents.
Paid link: we may earn a commission.
Find GKS18V-25CN prices on Amazon Find GKS18V-25CN prices at eBay New tab, US retailers. Search results open where no exact listing is on file. Check the listing says GKS18V-25CN and tool only; marketplace sellers vary.What is in the box with the GKS18V-25CN?
- IncludedTool: circular saw
- Not includedBattery: needs a Bosch 18V battery (see batteries)
- Not includedCharger (see chargers)
- Not listedCase or bag: not confirmed in the published box list
Also in the box: 7-1/4 In. 24-Tooth Carbide Circular Saw Blade, Hex Wrench
Runs on Bosch 18V batteries. Which batteries fit?
Model number ending "N": Bare tool: no battery or charger. How Bosch model numbers work.
Model number GKS18V-25CN (also searched without hyphens as GKS18V 25CN).
Quick answers
- Does the GKS18V-25CN come with a battery?
- No. The GKS18V-25CN is a bare tool: no battery and no charger in the box.
- Which batteries fit the GKS18V-25CN?
- It runs on Bosch 18V batteries. Which batteries fit, in Bosch's own words.
- What blade size does the GKS18V-25CN take?
- Blade diameter: 7-1/4 in, as Bosch publishes it.
- What is the GKS18V-25CN's top speed?
- Max speed: 5,000 RPM, as Bosch publishes it.
- What is the GKS18V-25CN warranty?
- 5 Year Limited Warranty (tool), as Bosch publishes it.
Ranked lists that include this circular saw
- Circular saws by blade diameter (35 models)
- Circular saws by max cut depth at 90 degrees (18 models)
- Circular saws by max cut depth at 45 degrees (18 models)
- Circular saws by max speed (29 models)
- Circular saws by max bevel (16 models)
- Circular saws by tool length (21 models)
Owner reviews
Read the owner reviews on BoschTools.com
Sources
- Bosch US product page GKS18V-25CN (features), retrieved 2026-10-25
Spotted a wrong number? Report a spec error (opens an email with the model filled in). We re-check against the maker's page and correct the page.